Chevrolet Equinox Service Manual: Trim Height Specifications
Measurement condition: Full tank of fuel, no passenger and placed on level surface.
P-235/60R17 | Equinox | 812± 12 mm (32.0 in± 0.5 in) | 835± 12 mm (32.9 in± 0.5 in) | 51± 10 mm (2.01 in± 0.4 in) | 39± 10 mm (1.54 in± 0.4 in) |
P-225/65R17 | Equinox | 820± 12 mm (32.2 in± 0.5 in) | 842± 12 mm (33.1± 0.5 in) | 51± 10 mm (2.01± 0.4 in) | 39± 10 mm (1.54± 0.4 in) |
P-235/55R18 | Equinox | 816± 12 mm (32.1± 0.5 in) | 839± 12 mm (33.0± 0.5 in) | 51± 10 mm (2.01± 0.4 in) | 39± 10 mm (1.54± 0.4 in) |
P-235/55R19 | Equinox | 828± 12 mm (32.6± 0.5 in) | 851± 12 mm (33.5± 0.5 in) | 51± 10 mm (2.01± 0.4 in) | 39± 10 mm (1.54± 0.4 in) |
P-235/60R17 | Terrain | 799± 12 mm (31.5± 0.5 in) | 831± 12 mm (32.7± 0.5 in) | 51± 10 mm (2.01± 0.4 in) | 39± 10 mm (1.54± 0.4 in) |
P-225/65R17 | Terrain | 807± 12 mm (31.8± 0.5 in) | 838± 12 mm (33.0± 0.5 in) | 51± 10 mm (2.01± 0.4 in) | 39± 10 mm (1.54± 0.4 in) |
P-235/55R18 | Terrain | 802± 12 mm (31.6± 0.5 in) | 833± 12 mm (32.8± 0.5 in) | 51± 10 mm (2.01± 0.4 in) | 39± 10 mm (1.54± 0.4 in) |
P-235/55R19 | Terrain | 815± 12 mm (32.1± 0.5 in) | 847± 12 mm (33.3± 0.5 in) | 51± 10 mm (2.01± 0.4 in) | 39± 10 mm (1.54± 0.4 in) |
| The front wheel opening height P-(P) is measured from the bottom lip of the wheelopening to the ground, measured at the center line of the front wheel.The rear wheel opening height R-(R) is measured from the bottom lip of the wheel openingto the ground, measured at the center line of the rear wheel.The rear suspension D Height is the difference (D=a-b) measured as a horizontal linethrough the center of the cradle attachment bolt-(a) and the center of the knuckleattachment bolt-(b). | |||||
Special Tools
IllustrationTool Number/ DescriptionJ-39570Chassis EarJ-8001Dial Indicator ...
Tire and Wheel Assembly-to-Hub/Axle Flange Match-Mounting Wheel Hub
Note:After remounting a tire and wheel assembly to a hub/axleflange, remeasure the tire and wheel assembly on-vehicle runout inorder to verify that the amount of runout has been reduced andbrought to ...
Other materials:
Drive Belt Tensioner Replacement Pulleys and Belts Belt Tensioner
Drive Belt Tensioner ReplacementCalloutComponent NamePreliminary ProcedureRemove the drive belt. Refer toDrive Belt Replacement.1Drive Belt Idler Pulley FastenerCaution:Refer toFastener Caution.Tighten58-Y (43-lb-ft)2Drive Belt Idler Pulley3Drive Belt Tensioner Fastener (Qty: 3)Tighten25-Y (18-lb-ft ...
