Chevrolet Equinox manuals

Chevrolet Equinox Service Manual: #PIT4720C: Odometer Servicing When The Odometer Cannot Be Set To The Actual Mileage - (May 2, 2013) Gauges Odometer

Chevrolet Equinox Service Manual / Body / Driver Info & Control / #PIT4720C: Odometer Servicing When The Odometer Cannot Be Set To The Actual Mileage - (May 2, 2013) Gauges Odometer

Subject:Odometer Servicing When The Odometer Cannot Be Set To The Actual Mileage

#PIT4720C: Odometer Servicing When The Odometer Cannot Be Set To The Actual Mileage - (May 2, 2013) Gauges Odometer

Models: 2014 and Prior GM Passenger Cars and Trucks
  

This PI was superseded to update model years. Please discard PIT4720B.

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) describedin this PI.

Condition/Concern

When replacing or servicing the IPC/odometer and the exchange center is unable toprogram the actual mileage on the odometer or the actual mileage is unknown, havethe dealer follow the instruction below.

Recommendation/Instructions

Refer the dealer to the GM SERVICE POLICIES AND PROCEDURES MANUAL section 3.2.4 ODOMETERSERVICING

3.2.4  Odometer Servicing

Various laws require that when an odometer is serviced, repaired or replaced, themileage indicated is to remain the same as before this service, repair or replacement.Where the odometer cannot register the same mileage as before, the odometer shallbe adjusted to read zero and a notice in writing shall be attached to the driver'sdoor frame of the vehicle (refer to illustration ODOMETER SERVICING LABEL).

It is the general practice of Authorized Service Centers to return repaired speedometersto their customers showing the original mileage reading on the odometer as received.This practice will apply whether or not the odometer unit is replaced. Therefore,a notice for the vehicle door frame indicating that an odometer has been set to zeronormally will not be required.

In those unusual instances when the odometer cannot be set to the actual vehicle mileage,it must be set at zero and a label such as indicated below, must be affixed to thedriver's door frame of the vehicle by the Service Agent. The Odometer Repair NoticeLabel may be obtained through GMCCA (Catalog Group 8.808).

SAMPLE LABEL:

ODOMETER REPAIR/REPLACEMENT

THE ODOMETER ON THIS VEHICLE WAS REPAIRED AND TURNED BACK TO ZERO, OR WAS REPLACEDWITH AN ODOMETER SET AT ZERO. MILEAGE PRIOR TO REPAIR/REPLACEMENT WAS:

_______________________MILES OR _______________________KILOMETERS.

DATE REPAIRED/REPLACED: __________

BY EMPLOYEE: _____________________________________________________

FEDERAL LAW PROHIBITS REMOVAL OR ALTERATION OF THIS LABEL

PT. NO. 10443718 ODOMETER REPAIR NOTICE

Please follow this diagnostic or repair process thoroughly and complete each step.If the condition exhibited is resolved without completing every step, the remainingsteps do not need to be performed.

GM bulletins are intended for use by professional technicians,NOT a "do-it-yourselfer".  They are written to inform thesetechnicians of conditions that may occur on some vehicles, or toprovide information that could assist in the proper service of avehicle.  Properly trained technicians have the equipment,tools, safety instructions, and know-how to do a job properly andsafely.  If a condition is described, DO NOT assume that thebulletin applies to your vehicle, or that your vehicle will havethat condition.  See your GM dealer for information on whetheryour vehicle may benefit from the information.

#PIT4720C: Odometer Servicing When The Odometer Cannot Be Set To The Actual Mileage - (May 2, 2013) Gauges Odometer

WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION

#07-08-49-020H: IPC Odometer Programming Method Quick Reference Guide - (Jun 5, 2013) Gauges Odometer
Subject:IPC Odometer Programming Method Quick Reference GuideModels: 2003-2014 GM Passenger Cars and TrucksAttention: This bulletin applies to vehicles sold in the U.S. and Canada Only.This bulletin ...

Instrument Cluster Scan Tool Information Gauges
Table 1: Instrument Cluster Scan Tool Data ParametersTable 2: Instrument Cluster Scan Tool Output ControlsInstrument Cluster Scan Tool Data ParametersParameterExpected ValueDescriptionOperating Condit ...

Other materials:

Front Side Marker Lamp Bulb Replacement (Terrain) Lighting Exterior Lighting Side Markers
Front Side Marker Lamp Bulb ReplacementCalloutComponent NamePreliminary ProcedureRemove the front wheelhouse front panel hole cover. Refer toFront Wheelhouse Front Panel Hole Cover Replacement.1Front Side Marker Lamp Bulb SocketProcedureRotate the bulb socket counter-clockwise and remove from thehea ...

© 2017-2019 Copyright www.cequinox.com