Chevrolet Equinox Service Manual: Instrument Cluster Scan Tool Information Gauges
| Table 1: | Instrument Cluster Scan Tool Data Parameters |
| Table 2: | Instrument Cluster Scan Tool Output Controls |
Operating Conditions: Ignition ON | ||
Ambient Air Temperature | 15-°C (59-°F) | The scan tool displays outside temperaturein-°C (°F). |
Battery Voltage | 12–14-V | The scan tool displays Volts. This is the current batteryvoltage signal. |
Boost Pressure Sensor | 0–100% | The scan tool displays the engine boost pressurefiltered. |
Coolant Level Switch | Open | The scan tool displays either Open, Closed, or NotAvailable. |
Driver Information Center Reset Switch | Active/Inactive | The scan tool displays Active or Inactive. This is the stateof the driver information center reset switch. |
Driver Information Center Switch | Varies | The scan tool displays Volts. This is the current driverinformation center switch input voltage. |
Driver Information Center Switch | Inactive | The scan tool displays either Inactive, Up, Down, or Menu.This is the state of the driver information center switch. |
Engine Coolant Temperature | °C (°F) | The scan tool displays actual engine coolant temperaturefiltered. |
Engine Oil Pressure | 103-kPa (15-PSI) to 241-kPa(35-PSI) | The scan tool displays the engine oil pressurefiltered. |
Engine Speed | RPM | The scan tool displays the actual engine speed. |
Fuel Level Sensor | % | The scan tool displays fuel level percent filtered. |
Key in Ignition Status | Active/Inactive | The scan tool displays Active or Inactive. This is the stateof the key in ignition switch. |
Odometer Lock Status | Active/Inactive | This is the state of vehicle odometer status. |
Reset Switch | Active/Inactive | The scan tool displays Active or Inactive. This is the stateof the reset switch. |
Vehicle Speed | km/h (MPH) | The scan tool displays the actual vehicle speed. |
Washer Fluid Heater | Off | The scan tool displays either Off, On, or NotAvailable. |
Washer Fluid Level Switch | Open | The scan tool displays either Open, Closed, or NotAvailable. |
All Indicators | This function is used to command all the indicators ON orOFF. |
CAN Bus Configuration Learn | This function is used to Reset the source ID for low speedCAN Bus communications. |
Driver Information Center Dimming | This function is used to command the dimming of the driverinformation display to Increase or Decrease by 10%. |
Driver Information Center Options | This function is used to command the driver informationcenter buttons using the scan tool. |
Driver Information Center Segments | This function is used to command the driver informationcenter segments ON and OFF. |
Instrument Cluster Gauge Sweep | This function is used to command the gauges to sweep fromminimum to maximum. |
Instrument Panel Dimmer Switch | This function is used to command the dimming of theinstrument cluster to Increase or Decrease by 10%. |
Odometer Programming | This function is used to command the odometer toreset. |
#PIT4720C: Odometer Servicing When The Odometer Cannot Be Set To The Actual Mileage - (May 2, 2013) Gauges Odometer
Subject:Odometer Servicing When The Odometer Cannot Be Set To The Actual MileageModels: 2014 and Prior GM Passenger Cars and Trucks This PI was superseded to update model years. Please discard PIT ...
Audible Warnings Description and Operation Gauges
The audible warnings alert the driver of a system concern or a critical vehicle condition.The radio generates the audible warnings through the speakers. The radio receivesaudible warning requests via ...
Other materials:
Oil Pan Assemble Engine Lubrication Oil Sump/Pan
Caution:Refer toFastener Caution.Install the oil pan drain plug-(1) and NEW O-ring seal-(2) and tighten to 25-Y (18-lb-ft).Install the NEW engine oil level switch seal-(1).Install the engine oil level switch-(3).Install the engine oil level switch bolts-(2) and tighten to 10-Y (89-lb-in).Install NEW ...
