Chevrolet Equinox manuals

Chevrolet Equinox Service Manual: Front Differential Drive Pinion Bearing Cup, Washer, and Lubricant Dam Replacement - Torque Converter Housing Side Automatic Transmission Unit

Chevrolet Equinox Service Manual / Powertrain / Transmission/Transaxle / Front Differential Drive Pinion Bearing Cup, Washer, and Lubricant Dam Replacement - Torque Converter Housing Side Automatic Transmission Unit

Table 1: Bearing Cup, Washer and Lubricant Dam Removal
Table 2: Bearing Cup, Washer and Lubricant Dam Installation
Bearing Cup, Washer and Lubricant Dam Removal

Front Differential Drive Pinion Bearing Cup, Washer, and Lubricant Dam Replacement - Torque Converter Housing Side Automatic Transmission Unit

up

Bearing Cup, Washer and Lubricant Dam Removal

Callout

Component Name

Preliminary Procedure

Do not install the bearing cup until after the selective washer measurement has beenperformed.

1

Front Differential Drive Pinion Gear Bearing Cup

Caution:Failure to apply the lubricant will cause damage to the boltand nut threads.

ProcedureTighten DT-45094 bearing cup remover until it fits snugly on the bearing cup.Adjust DT 45124 removal bridge so it sits on the torque converter housing surface just beyond the bearing cup opening.Apply the extreme pressure lubricant DT 23444-A extreme press lubricant to the puller bolt threads to prevent damage to the bolt threads during bearing cupremoval.Hold the puller bridge bolt and turn the nut to removal the bearing cup.Special ToolsDT 23444-A Extreme Press Lubricant-–-1/4 Ounce TubeDT-45087 Transfer Shaft and Differential Bearing Cup InstallerDT-45094 Bearing Cup RemoverDT 45124 Removal BridgeDT-47927 Bearing Cup Remover

For equivalent regional tools, refer toSpecial Tools.

2

Front Differential Drive Pinion Gear Bearing Thrust Washer

3

Front Differential Drive Pinion Gear Lube Dam

Special ToolsDT-48055 Lube Dam RemoverGE 6125-1B Slide Hammer with Adapter or equivalent

For equivalent regional tools, refer toSpecial Tools.

Bearing Cup, Washer and Lubricant Dam Installation

Front Differential Drive Pinion Bearing Cup, Washer, and Lubricant Dam Replacement - Torque Converter Housing Side Automatic Transmission Unit

Bearing Cup, Washer and Lubricant Dam Installation

Callout

Component Name

Preliminary Procedure

Do not install the bearing cup until after the selective washer measurement has beenperformed.

1

Front Differential Drive Pinion Gear Lube Dam

Special ToolsDT-46630 Lube Dam InstallerGE 8092 Driver Handle

For equivalent regional tools, refer toSpecial Tools.

2

Front Differential Drive Pinion Gear Bearing Thrust Washer

Note:Install the correct drive pinion gear bearing thrust washer as determined by the thrustwasher measurement procedure. Refer toFront Differential Drive Pinion Gear Bearing Thrust Washer and Front DifferentialBearing Washer Measurement.

3

Front Differential Drive Pinion Gear Bearing Cup

Caution:Support the back side of the torque converter housing beforeinstalling the bearing cup. Apply a light coating of transmissionfluid to the bore before pressing the cup into position. Installthe bearing cup until it stops moving. Applying excessive pressureto the bearing cup once it is seated could cause damage to thetorque converter housing casting.

Caution:An unseated or improperly installed bearing cup will resultin premature bearing failure. Visually inspect the bearing cup toinsure there is“no gap” between the converterhousing, thrust washer, and the bearing cup. Use of a feeler gaugemay assist in identifying a bearing cup that is not fullyseated.

Special Tools

DT-45087 Bearing Cup Installer

For equivalent regional tools, refer toSpecial Tools.

Transmission Parts Kit Specifications Automatic Transmission Unit
Table 1: A/Trans Seal Kit (Gen 1& 2) 24251028Table 2: Front Wheel Seal Kit (Gen 1& 2) 19258415Table 3: Front Wheel Seal Kit (Gen 1& 2) 19258416Table 4: A/Trans Seal Kit (Gen 1) 24251353 (1 of 2)Table ...

Transmission Parts Kit Specifications Automatic Transmission Unit
Table 1: Clutch Plate Pack 24240100Table 2: Front Wheel Drive Shaft Seal Kit 19258265Table 3: Front Wheel Drive Shaft Seal Kit 19258266Table 4: Control Valve Body Kit 24248118Table 5: A/Trans Service ...

Other materials:

Control Valve Body Assembly Installation Automatic Transmission Unit Control Valve Body
Control Valve Body Assembly InstallationCalloutComponent Name1Low and Reverse Clutch Fluid Passage Seal21-2-3-4 Clutch Fluid Passage Seal3Control Valve Body Spacer Plate Assembly4Control Valve Body AssemblyNote:Align the manual valve to the rod on the manual shaft.5Control Valve Body Bolt-M6-x-60-(Q ...

© 2017-2024 Copyright www.cequinox.com