Chevrolet Equinox manuals

Chevrolet Equinox Owners Manual: Clock

Base Radio

The infotainment system controls are used to access the time and date settings through the menu system. See Operation on how to use the menu system.

Setting the Time and Date

When Auto Set is enabled the time cannot be manually set.

  1.  Press , then touch SETTINGS.
  2.  Touch Time and Date, then Set Time or Set Date.
  3.  Touch + or − to adjust the value.
  4.  Touch or to adjust AM or PM for 12 hour format.
  5. Touch.

Using Auto Set

  1.  Press , then touch SETTINGS.
  2. Touch Time and Date, then Auto Set.
  3. Select from the available selections.
  4.  Touch.

Setting the 12/24 Hour Format

  1.  Press , then touch SETTINGS.
  2.  Touch Time and Date, then select 12h or 24h format.
  3.  Touch.

Setting the Month and Day Format

  1.  Press , then touch SETTINGS.
  2.  Touch Time and Date, then Set Date Format.
  3.  Select DD/MM/YYYY (day/ month/year), MM/DD/YYYY (month/day/year), or YYYY/ MM/DD (year/month/day) format.
  4.  Touch.

Uplevel Radio Using Faceplate Controls

To set the time or date:

  1.  Select Home Page, then select SETTINGS.
  2.  Select Time and Date, then the desired function.
  3.  Turn the MENU knob to increase or decrease the value.
  4.  Press the MENU knob to go to the next value. After the last value is selected, the system will update and return to the Settings menu. Press BACK to go to the last menu and save the changes.

Auto Set requires an OnStar subscription.

If auto timing is set, the time displayed on the clock may not update immediately when driving into a new time zone.

To set the clock display:

  1.  Select SETTINGS from the Home Page, then select Time and Date.
  2.  Select Clock Display.
  3.  Turn the MENU knob to Off or On.
  4.  Press the MENU knob to select.

Press BACK to go to the last menu and save the changes.

Uplevel Radio Using Touchscreen Controls

The infotainment system controls are used to access the time and date settings through the menu system. See "Using the System" under "Introduction" in the infotainment manual.

To set the time:

  1.  Touch SETTINGS from the Home Page, then touch Time and Date.
  2.  Touch Set Time and touch orto increase or decrease hours, minutes, and AM or PM.

    Touch 12-24 Hr for 12 or 24 hour clock.

  3. Touch to go back to the previous menu.

Auto Set requires an OnStar subscription.

If auto timing is set, the time displayed on the clock may not update immediately when driving into a new time zone.

To set the date:

  1.  Touch SETTINGS from the Home Page, then touch Time and Date.
  2.  Touch Set Date and touch orto increase or decrease month, day, or year.
  3.  Touch to go back to the previous menu.

To set the clock display:

  1.  Touch SETTINGS and touch Time and Date.
  2.  Touch Clock Display and touch OFF or ON to turn the clock display off or on.
  3.  Touch to go back to the previous menu.

The clock settings can also be accessed by touching the time display, then touching Set.

Compass
The vehicle may have a compass display on the Driver Information Center (DIC). The compass receives its heading and other information from the Global Positioning System (GPS) antenna, StabiliTra ...

Power Outlets
The vehicle has three 12-volt accessory power outlets, which can be used to plug in electrical equipment, such as a cell phone or MP3 player. There are power outlets:  On the center st ...

Other materials:

Engine Front Cover Installation Engine Block Cylinder Block Cyl Block Front Cover
Special Tools EN–46109 Guide PinsFor equivalent regional tools, refer toSpecial Tools.Install the 8-mm (0.315-in) guide from the EN–46109 pins into the cylinder block positions as shown.Install the NEW engine front cover to cylinder block seal.Note:No RTV sealant should be visible in the M12 bol ...

© 2017-2019 Copyright www.cequinox.com